Maintaining a clean and efficient Jandy CL580 filter is crucial for ensuring crystal-clear swimming pool water and extending the life of the filter itself. Proper cleaning removes dirt, debris, and accumulated particles that can clog the filter media and impede water flow, resulting in reduced filtration efficiency. Regular cleaning will not only improve your pool’s water quality but also save you time and money in the long run.
Before embarking on the cleaning process, it’s essential to gather the necessary tools and supplies. These include a filter cleaning solution, a garden hose with a spray nozzle, a bucket, a filter brush, and a pair of gloves. Ensure you have a dedicated cleaning area away from the pool to prevent any chemicals or debris from contaminating the water. Disconnect the filter from the power source and close the system valves before commencing the cleaning procedure.
To clean the filter cartridges, remove them from the housing and submerge them in a bucket filled with the filter cleaning solution. Allow them to soak for the recommended duration specified on the product label. Use a filter brush to gently agitate and dislodge any stubborn dirt or debris. Rinse the cartridges thoroughly with clean water from the garden hose, ensuring all traces of the cleaning solution are removed. Inspect the cartridges for any tears or damage and replace them if necessary. Reassemble the filter, reconnect it to the power source, and open the system valves. Your Jandy CL580 filter is now clean and ready to provide optimal filtration for your swimming pool.
Removing the Filter Cartridge
Before you begin, ensure the pump is turned off and disconnected from the power source. Wear protective gloves and goggles because the process involves working with chemicals.
1. Disconnect the filter housing: Locate the filter housing and unscrew the lid by turning it counterclockwise. You’ll encounter water, so be prepared for some spillage.
2. Remove the filter cartridge: Gently grasp the cartridge’s handle and pull it straight up and out of the housing. The cartridge may be heavy, so use caution.
3. Inspect the cartridge: Once removed, inspect the cartridge for any visible dirt, debris, or damage. If it’s excessively dirty, proceed to clean it; otherwise, you can reinstall it.
| Cartridge Condition | Action |
|---|---|
| Clean | Reinstall the cartridge |
| Dirty | Clean the cartridge |
| Damaged | Replace the cartridge |
4. Reinstall the filter cartridge: If the cartridge is clean, insert it back into the filter housing. Ensure it’s properly seated and the handle is pointing upwards.
5. Reconnect the filter housing: Screw the lid back onto the filter housing by turning it clockwise. Tighten it securely, but avoid overtightening.
6. Restart the pump: Reconnect the pump to the power source and turn it on. The system will circulate water through the clean cartridge, ensuring optimal filtration.
Cleaning the Filter Cartridge
1. Turn Off the Pump and Drain the Pool Water
Unplug the pump and allow the remaining water in the filter system to drain.
2. Remove the Filter Cartridge
Remove the filter cartridge housing and pull out the cartridge. Rinse the housing and o-ring with a garden hose to remove any debris.
3. Rinse the Filter Cartridge with Clean Water
Hold the filter cartridge upright and spray it with a strong stream of water from a garden hose. Start at the top and work your way down, making sure to rinse both the inside and outside of the pleats.
4. Use a Chemical Solution for Heavy Deposits
If the cartridge has heavy deposits of dirt, scale, or algae, soak it in a solution of filter cleaner and hot water for 30 minutes to 1 hour. Follow the manufacturer’s instructions carefully.
| Chemical Solution |
|---|
| 1 quart of filter cleaner to 5 gallons of hot water |
Rinse the cartridge thoroughly with clean water after soaking.
5. Inspect and Replace the Cartridge
Inspect the cartridge for any tears, punctures, or other damage. If the cartridge is damaged, replace it with a new one.
Checking for Leaks
It’s important to check the Jandy CL580 filter for leaks regularly to ensure its proper operation and prevent any potential damage to the equipment or surrounding area. Here’s how to check for leaks:
- Isolate the Filter: Shut off the pump and valves connected to the filter.
- Look for Obvious Leaks: Check the filter housing, connections, and valves for any visible signs of leaks, such as dripping or wet spots.
- Check the Pressure Gauge: Observe the pressure gauge on the filter. If the pressure drops significantly within a short period (e.g., 10 psi in 15 minutes), it could indicate a leak.
- Use a Leak Detector: Apply a leak detector solution or spray around the filter housing, connections, and valves. If there’s any leakage, you’ll see bubbles forming.
- Inspect the Filter Grids: Remove the filter grids and examine them for cracks or damage. Broken or damaged grids can cause leaks.
- Check the O-Rings and Gaskets: Inspect the O-rings and gaskets on the filter housing and connections for any wear or damage. Replace any damaged seals.
- Pressurize the Filter: Using a pool vacuum or garden hose, gently pressurize the filter without the grids in place. Watch for any leaks or weeping around the filter housing or connections.
| Leak Source | Possible Causes |
|---|---|
| Filter Housing | Damaged housing, loose connection, faulty O-ring |
| Connections | Loose fittings, damaged pipes, worn gaskets |
| Valves | Loose handles, broken seals, damaged valve body |
| Filter Grids | Cracked or broken grids |
| O-Rings and Gaskets | Wear, damage, improper installation |
Maintaining the Filter Regularly
To keep your Jandy CL580 filter functioning optimally, regular maintenance is essential. Here are the steps involved:
1. Checking the Pressure Gauge
Monitor the pressure gauge regularly. A significant increase in pressure (10 psi or more above normal) indicates a dirty filter that requires cleaning.
2. Cleaning the Hair and Lint Pot
Remove the hair and lint pot frequently to prevent clogs. Rinse the pot thoroughly with a garden hose.
3. Backwashing the Filter
Backwashing removes dirt and debris from the filter media. Backwash for 1-2 minutes every week or more frequently if the filter is heavily used.
4. Rinsing the Filter
After backwashing, rinse the filter for 30 seconds to clear any remaining debris.
5. Adding Chemicals
Maintain the proper chemical balance in your pool water. Follow the manufacturer’s instructions for adding chlorine, pH adjusters, and other necessary chemicals.
6. Inspecting the Filter Media
Periodically check the filter media for wear or damage. Replace the media if it is torn, discolored, or compacted.
7. Cleaning the Grids
Remove the filter grids and clean them thoroughly with a hose or brush to remove dirt and debris.
8. Lubricating the O-Rings
Lubricate the O-rings on the filter cap and other connections with a silicone-based lubricant to ensure a proper seal and prevent leaks.
Here’s a table summarizing the recommended frequency for each maintenance task:
| Task | Frequency |
|---|---|
| Check Pressure Gauge | Weekly |
| Clean Hair and Lint Pot | As needed |
| Backwash | Weekly |
| Rinse | After backwashing |
| Add Chemicals | As per manufacturer’s instructions |
| Inspect Filter Media | Monthly |
| Clean Grids | Monthly |
| Lubricate O-Rings | As needed |
Extended Filter Life Tips
1. Clean or Backwash Your Filter Regularly: Regular cleaning or backwashing removes dirt and debris, allowing the filter to work efficiently.
2. Check Pressure Gauge: A high pressure gauge reading indicates a dirty filter. Clean or backwash immediately.
3. Use a Pre-Filter: A pre-filter captures large debris, reducing the load on the main filter.
4. Use Quality Filter Media: High-quality filter media, such as sand or glass, filters more effectively.
5. Rinse Filter Thoroughly After Cleaning: Residual dirt or cleaner can accumulate over time.
6. Avoid Overloading: Do not fill the filter beyond the recommended capacity. Overloading can reduce filtration efficiency.
7. Inspect Regularly for Leaks: Leaks can damage the filter or waste water. Repair any leaks promptly.
8. Lubricate Gaskets: Lubricating gaskets ensures a proper seal and prevents leaks.
9. Replace Filter Media When Necessary: Over time, filter media becomes clogged and ineffective. Replace it according to the manufacturer’s guidelines.
10. Monitor Filter Performance and Make Gradual Adjustments:
a) Monitor the pressure gauge regularly and backwash the filter when the pressure increases by 10 psi above the clean pressure.
b) Gradually adjust the backwash time to ensure effective cleaning without wasting water.
| Backwash Pressure | Backwash Duration |
|---|---|
| 15-20 psi | 2-3 minutes |
| 20-25 psi | 3-4 minutes |
| 25-30 psi | 4-5 minutes |
How To Clean Jandy CL580 Filter
1. Turn off the pump and filter system.
2. Remove the filter lid by unscrewing the bolts that hold it in place.
3. Remove the filter cartridge by pulling it out of the filter housing.
4. Rinse the filter cartridge with a garden hose until the water runs clear.
5. If the filter cartridge is heavily soiled, you may need to soak it in a solution of water and filter cleaner for 30 minutes before rinsing it.
6. Reinsert the filter cartridge into the filter housing and tighten the bolts that hold it in place.
7. Replace the filter lid and tighten the bolts that hold it in place.
8. Turn on the pump and filter system.
People Also Ask About How To Clean Jandy CL580 Filter
How often should I clean my Jandy CL580 filter?
You should clean your Jandy CL580 filter every 2-4 weeks, depending on how often you use your pool.
What are the signs that my Jandy CL580 filter needs to be cleaned?
The signs that your Jandy CL580 filter needs to be cleaned include decreased water flow, increased pressure on the filter gauge, and cloudy water.
Can I use a pressure washer to clean my Jandy CL580 filter?
No, you should not use a pressure washer to clean your Jandy CL580 filter. The high pressure of the water can damage the filter cartridge.
