Maintaining a clean home environment is essential for both your health and well-being. One crucial aspect of achieving this is ensuring that your Shark Flexstyle vacuum cleaner is operating at its best. Over time, however, dirt, dust, and debris can accumulate in its filter, hindering its performance and potentially affecting indoor air quality. In this article, we will provide a step-by-step guide on how to clean the Shark Flexstyle filter effectively, restoring its functionality and ensuring optimal air purification in your home.
Before embarking on the cleaning process, it’s important to gather the necessary materials. You will need a vacuum cleaner with a hose attachment, a soft brush or cloth, and a clean sink or bucket. Additionally, ensure that the vacuum cleaner is unplugged from the power outlet for safety reasons. To begin, remove the filter from the vacuum cleaner by pressing the release button located on the filter housing. Once the filter is detached, you can proceed with the cleaning steps outlined below.
Firstly, use the vacuum cleaner hose attachment to gently remove any loose dirt or debris from the filter. This will help to dislodge any large particles that may have accumulated on the filter surface. Afterward, rinse the filter thoroughly under running water from the sink or bucket. While rinsing, gently agitate the filter to loosen any remaining dirt or grime. Avoid using harsh detergents or chemicals, as these may damage the filter material. Once the filter is thoroughly rinsed, shake it vigorously to remove excess water. Finally, allow the filter to air dry completely before reinserting it back into the vacuum cleaner. By following these steps, you can effectively clean the Shark Flexstyle filter, ensuring optimal performance and maintaining a healthy home environment.
Identifying the Filter Type
Shark Flexstyle vacuums are equipped with two types of filters: the pre-motor filter and the HEPA filter. The pre-motor filter is located near the brushroll, while the HEPA filter is located near the exhaust port. It’s crucial to identify the correct filter type to ensure efficient cleaning and optimal performance of your vacuum cleaner.
Pre-Motor Filter Identification:
The pre-motor filter is typically made of foam and is designed to capture larger dust particles and debris before they reach the motor. It is usually located near the brushroll, either inside the dustbin or directly behind it. To identify the pre-motor filter, refer to the vacuum’s user manual or look for a foam filter component near the brushroll area. Cleaning the pre-motor filter regularly is essential to maintain the vacuum’s suction power and prevent dust buildup within the motor.
| Pre-Motor Filter Location | Description |
|---|---|
| Inside the dustbin | Foam filter located at the bottom of the dustbin |
| Behind the brushroll | Foam filter situated behind the rotating brushroll |
Removing the Filter
The Shark Flexstyle vacuum cleaner has a washable filter that needs to be cleaned regularly to maintain optimal suction power. Here’s a step-by-step guide on how to remove the filter:
1. Detach the dirt tank from the main unit by pressing the release button and pulling straight up.
2. Open the dirt tank by pressing the latch on the bottom. The filter is located on the inside of the tank.
3. To remove the filter, press the blue tab on the top of the filter and pull it straight up. Be careful not to touch the filter material.
Cleaning the Filter
The filter can be washed with warm water and a mild detergent. Do not use bleach or harsh chemicals. Rinse the filter thoroughly and allow it to air dry completely before reattaching it to the dirt tank.
Reattaching the Filter
Once the filter is dry, reattach it to the dirt tank by inserting it into the slot on the inside of the tank. Make sure the filter is fully inserted and the blue tab is locked into place.
Reattach the dirt tank to the main unit and you’re ready to vacuum again.
Here’s a summary of the steps in a table format:
| Step | Action |
|---|---|
| 1 | Detach the dirt tank. |
| 2 | Open the dirt tank. |
| 3 | Remove the filter by pressing the blue tab and pulling it straight up. |
| 4 | Rinse the filter thoroughly with warm water and a mild detergent. |
| 5 | Allow the filter to air dry completely. |
| 6 | Reattach the filter to the dirt tank. |
| 7 | Reattach the dirt tank to the main unit. |
Cleaning the Filter Foam
Remove the Filter Foam
Locate the filter foam on the bottom of the vacuum cleaner. Depress the release button and pull the filter foam straight up to remove it.
Rinse the Filter Foam
Use cold, running water to rinse the filter foam thoroughly. Avoid using hot water, as this can damage the foam.
Squeeze Out Excess Water
Gently squeeze out any excess water from the filter foam. Do not twist or wring the foam, as this can damage it.
Air Dry the Filter Foam
Place the filter foam in a well-ventilated area to air dry completely. Avoid placing the filter foam in direct sunlight, as this can cause it to become brittle.
Note:
It is recommended that you clean the filter foam regularly to maintain optimal suction performance. The frequency of cleaning will vary depending on how often you use your vacuum cleaner. If you notice a decrease in suction power, it is a good idea to check the filter foam and clean it if necessary.
| Reccommended time for filter replacement |
|---|
| Monthly for heavy use |
| Bimonthly for moderate use |
| Quarterly for light use |
Cleaning the Felt Filter
The felt filter is located on the bottom of the Shark Flexstyle vacuum cleaner. It is responsible for capturing fine dust and debris from the air. To clean the felt filter, follow these steps:
-
Unplug the vacuum cleaner from the power outlet.
-
Remove the dust cup by pressing the release button on the top of the vacuum cleaner.
-
Remove the felt filter from the bottom of the dust cup.
-
Rinse the felt filter with cold water until the water runs clear.
-
**GentlySqueeze Out Excess Water:
Once you have rinsed the felt filter, gently squeeze out any excess water.
- Avoid wringing or twisting the filter, as this can damage the fibers.
- Use a clean towel to absorb any remaining moisture.
- Allow the filter to air-dry completely before reinserting it into the vacuum cleaner.
-
Reinsert the felt filter into the bottom of the dust cup.
-
Reattach the dust cup to the vacuum cleaner.
-
Plug the vacuum cleaner back into the power outlet and resume use.
Resetting the Filter Indicator
Resetting the filter indicator is a simple process that can be completed in just a few steps. Follow these instructions to reset the indicator:
Step 1: Locate the Filter Reset Button
The filter reset button is located on the bottom of the Shark Flexstyle vacuum cleaner. It is a small, black button with a corresponding label. It is located near the dustbin release button.
Step 2: Press and Hold the Reset Button
Once you have located the filter reset button, press and hold it for approximately 5 seconds. The filter indicator light will begin to flash.
Step 3: Release the Reset Button
Once the filter indicator light has started flashing, release the reset button. The light will continue to flash for a few more seconds before turning off.
Step 4: Replace the Filter
Once the filter indicator light has turned off, you can replace the old filter with a new one. Be sure to insert the new filter correctly, as indicated in the vacuum cleaner’s user manual.
Step 5: Check the Filter Indicator
After replacing the filter, check the filter indicator light to ensure that it has reset. The light should be off, indicating that the filter is clean and ready to use.
Step Action 1 Locate the Filter Reset Button 2 Press and Hold the Reset Button for 5 Seconds 3 Release the Reset Button 4 Replace the Filter 5 Check the Filter Indicator How to Clean Shark Flexstyle Filter
The Shark Flexstyle filter is an important part of your vacuum cleaner, and it needs to be cleaned regularly to keep your vacuum running at its best. Here are the steps on how to clean your Shark Flexstyle filter:
- Turn off and unplug the vacuum cleaner.
- Locate the filter. The filter is located in the top of the vacuum cleaner, behind the dustbin.
- Remove the filter. To remove the filter, press the release button on the top of the vacuum cleaner and pull the filter straight up.
- Clean the filter. You can clean the filter by rinsing it with water or by using a vacuum cleaner to remove the dust and dirt.
- Allow the filter to dry completely. Before you put the filter back in the vacuum cleaner, make sure it is completely dry.
- Reinstall the filter. To reinstall the filter, simply push it back into place in the top of the vacuum cleaner.
- Plug in and turn on the vacuum cleaner.
Your Shark Flexstyle filter is now clean and ready to use.
People Also Ask
How often should I clean my Shark Flexstyle filter?
You should clean your Shark Flexstyle filter every 2-3 months, or more often if you vacuum frequently.
Can I wash my Shark Flexstyle filter in the dishwasher?
No, you should not wash your Shark Flexstyle filter in the dishwasher. The dishwasher’s heat and detergent can damage the filter.
Where can I buy a replacement Shark Flexstyle filter?
You can buy a replacement Shark Flexstyle filter at most major retailers, or online.
-
