If you’re grappling with a malfunctioning Roper washing machine, resetting it could be the key to restoring its functionality. This simple yet effective troubleshooting step can resolve a plethora of common issues, ranging from frozen cycles to persistent error codes. Unlike more complex repairs that necessitate the expertise of a skilled technician, resetting your Roper washing machine is a task you can effortlessly accomplish on your own.
Before embarking on the resetting procedure, ensure that the washing machine is unplugged from the power outlet. This safety precaution will prevent any electrical shocks during the reset process. Once the machine is safely disconnected, locate the control panel and identify the “Reset” button. If your washing machine model lacks a dedicated “Reset” button, a combination of button presses may be required to initiate the reset. Consult your user manual for specific instructions tailored to your particular model.
Resetting Your Roper Washing Machine
If your Roper washing machine is experiencing any issues, resetting it may resolve the problem. Here’s a step-by-step guide on how to reset your Roper washing machine:
Step 1: Unplug the Washing Machine
1. Start by unplugging the washing machine from the electrical outlet. This cuts off the power supply to the machine and allows for a complete reset.
2. Wait for a few minutes to ensure that all the power has dissipated from the machine.
3. Locate the circuit breaker or fuse box and switch off the breaker or remove the fuse corresponding to the washing machine. This additional step ensures the power supply to the washing machine is completely isolated.
Step 2: Open and Close the Lid
1. Open the lid of the washing machine.
2. Close the lid and hold it shut for several seconds.
3. Repeat this step several times to initiate a hard reset.
Step 3: Replug the Washing Machine
1. Find the electrical outlet where the washing machine was plugged in.
2. Before plugging it back in, check to make sure the circuit breaker or fuse has been turned on again to restore power to the machine.
3. Plug the washing machine back into the outlet.
4. Turn on the washing machine and select a wash cycle.
5. The washing machine should now be reset and functioning properly. If the problem persists, you may need to contact a professional appliance repair technician.
Identifying the Reset Button
Locating the reset button on a Roper washing machine can vary depending on the model. Follow the steps below to identify the reset button on your specific model:
- Check the front control panel: On some Roper washing machines, the reset button is located on the front control panel, typically near the start/pause button or the power button.
- Examine the top control panel: For models with a top control panel, the reset button may be situated towards the back or side of the control panel, sometimes nestled near the lid switch or the detergent dispenser.
- Look for a small, recessed button: The reset button is typically small and recessed, meaning it is sunk into the surface of the control panel. It may have a label that reads “RESET” or a similar indication.
- Refer to the user manual: If you are unable to locate the reset button using the methods mentioned above, consult the user manual for your specific Roper washing machine model. The manual will provide detailed instructions on how to locate and use the reset button.
Once you have identified the reset button, proceed to the next section to learn how to reset your Roper washing machine.
Performing a Soft Reset
Step 1: Unplug the Washing Machine
Disconnect the Roper washing machine from the power outlet. Wait for 60 seconds to allow the power to discharge.
Caution: Never touch the electrical components of the washing machine with wet hands.
Step 2: Plug the Washing Machine Back In
After 60 seconds, reconnect the washing machine to the power outlet.
Step 3: Press and Hold the Cycle Selector Knob
Locate the cycle selector knob on the washing machine’s control panel. Press and hold the knob down for 10 seconds.
Step 4: Release the Knob and Turn it to the Off Position
Release the cycle selector knob and turn it to the “Off” position.
Step 5: Start a New Cycle
Select the desired washing cycle and press the “Start/Pause” button to initiate the new cycle. The soft reset is now complete.
Executing a Hard Reset
A hard reset can be performed if a soft reset does not resolve the issue. This will clear all settings and stored data, including any custom cycles or preferences you have set. To perform a hard reset:
- Unplug the washing machine from the power outlet.
- Wait 60 seconds.
- Plug the washing machine back into the power outlet.
-
Turn the dial to any cycle and hold down the “Start/Pause” button for 5-10 seconds.
Make/Model Button Combination Roper RTW4516FW Hold “Start/Pause” for 5 seconds Roper RTW4675XQ Hold “Start/Pause” for 10 seconds - Release the “Start/Pause” button.
- The washing machine will start the selected cycle.
Resetting a Front-Load Model
For front-load Roper washing machines, the reset process is slightly different. Follow these steps:
- Unplug the washing machine from the power outlet.
- Wait 1 minute for the machine to completely power down.
- Press and hold the “Normal” and “Eco” buttons simultaneously.
- While holding the buttons, plug the washing machine back into the power outlet.
- Continue holding the buttons for 5 seconds. The machine should start to beep and the display will flash. This indicates that the reset is complete.
Detailed Explanation of Step 5:
| Steps | Description |
|---|---|
| Hold buttons for 5 seconds | Continue holding the “Normal” and “Eco” buttons for the full 5 seconds. Do not release the buttons prematurely. |
| Beeping and flashing display | When the reset is successful, the washing machine will emit a series of beeps and the display will flash. This typically occurs within 5 seconds of holding the buttons. |
| Reset complete | Once the beeping and flashing stop, the reset process is complete. The display will return to its normal state and the machine will be ready for use. |
Resetting a Top-Load Model
To reset a top-load Roper washing machine, follow these steps:
- Unplug the machine. This will cut off the power supply to the washer and allow it to reset.
- Wait 60 seconds. This will give the washing machine time to fully reset.
- Plug the machine back in.
- Select the desired cycle and press start.
Detailed Steps for Step 6
Step 6 of the resetting process involves selecting the desired cycle and pressing the start button. Here are the detailed steps for this step:
- Locate the cycle selector dial on the washing machine’s control panel.
- Use the dial to select the desired cycle for your laundry load.
- Press the start button, which is typically located next to the dial or on the front of the washing machine.
- The washing machine will begin the selected cycle.
If the washing machine does not start after pressing the start button, repeat steps 1-5 of the resetting process and try again.
Unplug the Washing Machine
The first step in resetting your Roper washing machine is to unplug it from the electrical outlet. This will cut off the power supply to the machine and allow it to reset.
Wait for One Minute
Once you have unplugged the washing machine, wait for one minute before plugging it back in. This will give the machine time to completely reset.
Plug the Washing Machine Back In
After one minute has passed, plug the washing machine back into the electrical outlet. The machine should now be reset and ready to use.
Troubleshooting Error Codes
If your Roper washing machine is displaying an error code, you can use the following table to troubleshoot the issue:
| Error Code | Description | Solution |
|---|---|---|
| E1 | The door is not closed properly. | Close the door firmly. |
| E2 | The water pressure is too low. | Check the water pressure at the faucet. If the pressure is low, adjust it by turning the handle on the faucet. |
| E3 | The water temperature is too high. | Adjust the water temperature setting on the washing machine. |
| E4 | The drain hose is clogged. | Unclog the drain hose by removing any debris that is blocking it. |
| E5 | The motor is not working properly. | Contact a qualified appliance repair technician. |
| E6 | The control board is not working properly. | Contact a qualified appliance repair technician. |
Resetting the Control Board
If you have tried all of the above troubleshooting steps and your washing machine is still not working, you may need to reset the control board. To do this, follow these steps:
- Unplug the washing machine from the electrical outlet.
- Remove the two screws that hold the control board in place.
- Gently pull the control board out of the machine.
- Wait for one minute.
- Plug the control board back into the machine.
- Tighten the two screws.
- Plug the washing machine back into the electrical outlet.
Clearing the Control Lock
The control lock feature prevents the washing machine from being accidentally started or stopped. If the control lock is engaged, the control panel will be disabled and the door will be locked. To clear the control lock, follow these steps:
1. Locate the control lock button.
The control lock button is usually located on the control panel, near the start/pause button. It may be labeled “Control Lock” or “Child Lock.”
2. Press and hold the control lock button.
Press and hold the control lock button for 3 seconds. The control lock indicator light will turn off and the control panel will be unlocked.
3. If the control lock button does not work, try the following:
- Unplug the washing machine from the power outlet.
- Wait 60 seconds.
- Plug the washing machine back into the power outlet.
- Press and hold the control lock button for 3 seconds.
4. If the control lock still does not work, you may need to reset the washing machine’s computer. To reset the computer, follow these steps:
- Unplug the washing machine from the power outlet.
- Wait 5 minutes.
- Plug the washing machine back into the power outlet.
- Press the start/pause button to start the washing machine.
The washing machine will now be reset and the control lock should be cleared.
| Operation | Control Lock Status |
|---|---|
| Control lock button is pressed | Control lock is enabled |
| Control lock button is pressed for 3 seconds | Control lock is disabled |
| Washing machine is unplugged | Control lock is reset |
Restoring Factory Settings
If you’re having trouble with your Roper washing machine, resetting it to factory settings may help. Here’s how to do it:
1. Unplug the washing machine from the power outlet.
2. Wait 60 seconds.
3. Plug the washing machine back in.
4. Turn the washing machine on.
5. Press and hold the “Start/Pause” button for 5 seconds.
6. The washing machine will beep and the lights will flash.
7. Release the “Start/Pause” button.
8. The washing machine will now be reset to factory settings.
9. Run a test cycle to make sure the washing machine is working properly.
Here is a table of the different error codes that can be displayed on the Roper washing machine:
| Error Code | Description |
|---|---|
| E01 | Door is open |
| E02 | Water level is too high |
| E03 | Water level is too low |
| E04 | Drain hose is clogged |
| E05 | Inlet hose is clogged |
| E06 | Pressure switch is faulty |
| E07 | Temperature sensor is faulty |
| E08 | Motor is faulty |
| E09 | Control board is faulty |
1. Unplug the Washer
Unplug the washer from its electrical outlet and wait at least one minute. During that waiting period, the washer will discharge any stored voltage, resetting internal components and erasing any error codes.
2. Replug the Washer
Plug the washer back in and allow it to run through a complete wash cycle without adding any laundry. This will help clear any residual error codes that may have prevented the reset.
3. Press the Start/Pause Button
To initiate the reset, press and hold the “Start/Pause” button for 5 seconds. The washer’s lights will flash or blink during this time, indicating that the reset is in progress.
4. Release the Button
Once the lights have stopped flashing, release the “Start/Pause” button. The washer should now be reset and ready for use.
5. Check the Display
Some Roper washers have digital displays that show error codes or status messages during the reset process. If an error code is displayed, refer to the washer’s manual for troubleshooting.
6. Run a Test Cycle
To ensure the reset was successful, run a small load of laundry through a complete wash cycle. Observe the washer’s performance to verify that it operates normally.
7. Clean the Drain Filter
A clogged drain filter can prevent the washer from operating properly. If the reset fails, check and clean the drain filter to remove any accumulated debris.
8. Check the Water Supply
Make sure that the water supply to the washer is turned on and that the hoses are properly connected. Insufficient water supply or blockages in the hoses can interfere with the reset process.
9. Contact Customer Support
If the reset fails or the washer still malfunctions, contact Roper customer support for further assistance and troubleshooting.
Additional Tips for Successful Resets
| Tip | Description |
|---|---|
| Wait Long Enough | Allow at least one minute after unplugging the washer before replugging it to ensure sufficient time for discharging stored voltage. |
| Power Surge Protection | Use a surge protector to prevent damage to the washer in case of voltage fluctuations during the reset process. |
| Avoid Overloading | Do not overload the washer during the test cycle, as this can strain the motor and interfere with the reset. |
| Check Error Codes | If an error code is displayed on the washer’s display, troubleshoot the issue and address it before attempting the reset again. |
| Contact Support Promptly | If multiple resets fail or the washer continues to malfunction, do not delay in contacting customer support for professional assistance. |
How To Reset Roper Washing Machine
If your Roper washing machine is not working properly, you may need to reset it. Resetting the washing machine will clear any errors that may have been stored in the memory and will restore the machine to its factory default settings.
To reset your Roper washing machine, follow these steps:
- Unplug the washing machine from the power outlet.
- Wait 60 seconds.
- Plug the washing machine back into the power outlet.
- Press and hold the “Start/Pause” button for 5 seconds.
- The washing machine will reset and the lights will flash.
Once the washing machine has reset, you can use it as normal.
People Also Ask About How To Reset Roper Washing Machine
Why is my Roper washing machine not working?
There are a few reasons why your Roper washing machine may not be working. Some of the most common reasons include:
- The washing machine is not plugged in.
- The water supply to the washing machine is turned off.
- The door to the washing machine is not closed properly.
- The washing machine is overloaded.
- There is a problem with the washing machine’s motor.
- There is a problem with the washing machine’s control panel.
How do I fix a Roper washing machine that is not working?
To fix a Roper washing machine that is not working, you will need to troubleshoot the problem. Some of the things you can do to troubleshoot the problem include:
- Checking to make sure that the washing machine is plugged in.
- Checking to make sure that the water supply to the washing machine is turned on.
- Checking to make sure that the door to the washing machine is closed properly.
- Checking to make sure that the washing machine is not overloaded.
- Checking to make sure that there is no problem with the washing machine’s motor.
- Checking to make sure that there is no problem with the washing machine’s control panel.
How do I reset my Roper washing machine?
To reset your Roper washing machine, follow these steps:
- Unplug the washing machine from the power outlet.
- Wait 60 seconds.
- Plug the washing machine back into the power outlet.
- Press and hold the “Start/Pause” button for 5 seconds.
- The washing machine will reset and the lights will flash.
